Office of Steam Logo_1

« previous next »
Pages: [1]

Author Topic: Steaming a Stuart Double 10V using a Jerry Rigging  (Read 1210 times)

  • Full Member
  • ***
  • Posts: 617
  • Location: Plano, Texas
Steaming a Stuart Double 10V using a Jerry Rigging
« on: October 28, 2024, 06:02:22 pm »
Today I wanted to steam my Double 10V by impulse so I jerry rigged it.    My Stuart boiler is still under repair but the Jensen boiler puts out plenty of power to run this engine.

I also jerry rigged an oil catch, as seen.

Steam test, before mounting to permanent board.




https://www.youtube.com/shorts/H70dPcKkZsc
Logged
The steam engine has done much more for science than science has done for the steam engine.”

― Lord Kelvin

  • Full Member
  • ***
  • Posts: 617
  • Location: Plano, Texas
Re: Steaming a Stuart Double 10V using a Jerry Rigging
« Reply #1 on: October 28, 2024, 10:53:49 pm »
[ Guests cannot view attachments ]
[ Guests cannot view attachments ]
Logged
The steam engine has done much more for science than science has done for the steam engine.”

― Lord Kelvin

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Steaming a Stuart Double 10V using a Jerry Rigging
« Reply #2 on: October 29, 2024, 12:04:02 am »
What's the white stuff in the bottom of the firebox Travis?
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Full Member
  • ***
  • Posts: 617
  • Location: Plano, Texas
Re: Steaming a Stuart Double 10V using a Jerry Rigging
« Reply #3 on: October 29, 2024, 12:37:23 am »
Quote from: Jim on October 29, 2024, 12:04:02 am
What's the white stuff in the bottom of the firebox Travis?

It is a heat retardant/ insulator that Charlie gave me a long while ago.
Logged
The steam engine has done much more for science than science has done for the steam engine.”

― Lord Kelvin

  • Full Member
  • ***
  • Posts: 726
  • Steam passionate and collector
  • Location: Saint-Mandé (France)
    • MYCP
Re: Steaming a Stuart Double 10V using a Jerry Rigging
« Reply #4 on: October 29, 2024, 08:38:43 am »
Bonjour Travis,

The D10 is my preferred steam macine, it is always a pleasure for me to see one operating smoothly.

My concern about it is its bad abililty to rust ==> how do you prevent yours from rusting ?

Mines have a little nut on the cylinde head to onsert oil after each run :

Logged
Raphaël, Membre du Modèle Yacht Club de Paris : http://mycparis.fr/
Membre de l'Offshore Club de Paris: http://site-ocparis.wifeo.com/
Youtube : https://www.youtube.com/rhavrane

  • Full Member
  • ***
  • Posts: 617
  • Location: Plano, Texas
Re: Steaming a Stuart Double 10V using a Jerry Rigging
« Reply #5 on: October 29, 2024, 10:02:12 am »
Quote from: Raphael on October 29, 2024, 08:38:43 am
Bonjour Travis,

The D10 is my preferred steam macine, it is always a pleasure for me to see one operating smoothly.

My concern about it is its bad abililty to rust ==> how do you prevent yours from rusting ?

Mines have a little nut on the cylinde head to onsert oil after each run :



I really need to look into that, however on all my engines I usually put some oil into the cylinder bore; if they will be idle a long time.  I run them so frequently that this usually isn’t an issue.  But, I also realize this D10 is using cast iron not gun metal, thus probably need to invest in an air compressor.

This D10 has an oiler installed.
Logged
The steam engine has done much more for science than science has done for the steam engine.”

― Lord Kelvin
Pages: [1]
« previous next »