Post by: Fullraceflathead on January 09, 2020, 02:45:14 pm
Hello.Great Idea, thanks for the dimensions.
for your information.
I made new springs with 0.3mm (0.0118 inch) steel wire, length 11mm (0.433 inch) diameter 4mm (0.157 inch)
good idle operation.
Greetings Christian.
https://youtu.be/8QsbLyE0zDk
Post by: rodnoc on December 26, 2019, 03:16:30 am
Post by: Belugawhaleman on December 25, 2019, 02:12:15 am
Post by: IndianaRog on October 22, 2019, 05:16:02 pm
Roger
Post by: odu50 on October 22, 2019, 03:21:55 pm
Christian, where did you get the fuel tank valve and the exhaust stack? I assume you machined them, but if there is an online source I would love to make those mods to my M90 and M91.Hi Roger.
thank you,
Roger
the exhaust stack Yes, I engined myself.
the fuel tank valve, I bought it here
https://www.dampfmodellbau.ch/?c=8
the first M 5x0.5
Post by: IndianaRog on October 21, 2019, 08:59:32 pm
thank you,
Roger
Post by: odu50 on October 20, 2019, 04:37:43 pm
Christian, I very much like your new and much sturdier fuel tank mounting brackets.
Very well done!
Gil
Thank Gil.
Post by: odu50 on October 20, 2019, 04:36:15 pm
Very nice runner Christian!Hello Rob.
What fuel are you using?
Is there any oil mixed in?
What is your ignition timing?
Sehr netter Läufer Christian!
Welchen Kraftstoff verwenden Sie?
Ist Öl eingemischt?
Was ist Ihr Zündzeitpunkt?
Thanks, Rob
I use Coleman fuel without added oil, I put oil in the lubricator.
The ignition is a little bit before the dead point high, Can be 1 or 2 degrees.
Post by: RedRyder on October 20, 2019, 02:49:55 pm
Very well done!
Gil
Post by: RobA on October 19, 2019, 09:32:08 pm
What fuel are you using?
Is there any oil mixed in?
What is your ignition timing?
Sehr netter Läufer Christian!
Welchen Kraftstoff verwenden Sie?
Ist Öl eingemischt?
Was ist Ihr Zündzeitpunkt?
Thanks, Rob
Post by: St Paul Steam on September 24, 2019, 08:06:22 am
Post by: odu50 on September 24, 2019, 03:07:22 am
I absolutely love the exhaust note, & will probably "borrow" the fuel shut off idea as well...Nicely done that 👍Hello
Thank you for your good comments
Just a piece of information.
With the fuel valve, there is a fear of an air bubble remaining in the pipe, if there is an air bubble, the engine does not work well.
Christian.
Post by: Stoker on September 23, 2019, 02:42:14 pm
Post by: St Paul Steam on September 23, 2019, 01:58:57 pm
Post by: txlabman on September 23, 2019, 01:42:26 pm
Very nice job on these modifications!
Post by: JinMachine on September 22, 2019, 06:38:01 pm
Post by: odu50 on September 22, 2019, 03:51:55 pm
One more small improvement
Greetings from Geneva.
Christian.
https://youtu.be/doaHY1VlyZo
Post by: RedRyder on September 15, 2019, 09:55:02 pm
Post by: Stoker on September 15, 2019, 08:07:22 pm
Seems like your modifications to the M90 have resulted in very smooth, stead and reliable operation .... well done!
Post by: odu50 on September 15, 2019, 04:36:40 pm
for your information.
I made new springs with 0.3mm (0.0118 inch) steel wire, length 11mm (0.433 inch) diameter 4mm (0.157 inch)
good idle operation.
Greetings Christian.
https://youtu.be/8QsbLyE0zDk
Post by: odu50 on September 15, 2019, 04:21:27 pm
Welcome aboard, Christian!Thank You Gil
Gil
Post by: RedRyder on September 11, 2019, 06:45:34 am
Gil
Post by: odu50 on September 10, 2019, 03:46:58 pm
Bonjour Christian,Hello raphäel.
Happy to see you there ;)
I would kindly suggest to introduce you there https://www.officeofsteamforum.com/meet-our-members/ and also share your beautiful models, especially the coal fired ones
thank you for your message, But, I do not read English fluently, I have to translate everything so it takes me a lot of time.
Post by: odu50 on September 10, 2019, 03:35:21 pm
Nice Work! 8) Thank you for sharing ;)Exactelly, the engine is less cooled with the long exhaust pipe.
Also like the added oilers and custom exhaust. Have you noticed a running temperature change with the new exhaust?
But, it's for the look, Cooling is the water that does it well, and the engine does not work in an industrial way, I always watch him.
Post by: Raphael on September 10, 2019, 03:05:00 pm
Happy to see you there ;)
I would kindly suggest to introduce you there https://www.officeofsteamforum.com/meet-our-members/ and also share your beautiful models, especially the coal fired ones
Post by: Dr.Rev.DelmarMacReady on September 10, 2019, 02:59:10 pm
Post by: Nick on September 10, 2019, 02:52:11 pm
Also like the added oilers and custom exhaust. Have you noticed a running temperature change with the new exhaust?
Post by: odu50 on September 10, 2019, 02:37:07 pm
By this message I would like to share some modifications that I made on my engine.
Greetinge from Switzerland.
https://youtu.be/ijKJqkujP34