Office of Steam Forum for Model & Toy Steam Gas & Hot Air Engines

The Regular Stuff: Chat, Buy, Sell, Off Topic, etc. => General Discussion - Scale Model Gas Engines - Hit & Miss - Throttle Governed - Non-Compression – etc => Topic started by: MasonvilleEngines on March 25, 2019, 02:59:09 pm

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on June 25, 2019, 10:23:36 am

Thanks Nick,
 I am sure there are more entertaining/informative videos, but if you liked that one...

Len.

https://youtu.be/9eIgttl9QEc

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: Nick on June 23, 2019, 07:52:48 pm

Another great video Len

(https://www.officeofsteamforum.com/proxy.php?request=http%3A%2F%2Femojiart.info%2Fwp-content%2Fuploads%2F2017%2F09%2FPopcorn-Emoji-smile.jpg&hash=aedfa5504756f45d0441813a9deab072da910201)

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on June 23, 2019, 12:52:29 pm

Hi all,
 Finally got Big Brother to cooperate, need a heavier exhaust spring.

Len.

https://youtu.be/tGAYGrDy8do

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: RedRyder on May 29, 2019, 06:02:19 am

Thanks for the Memorial Day Gas Up videos.


Great fun Herb's engines are!

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: txlabman on May 29, 2019, 12:08:39 am

Somehow I missed this thread earlier.

Thanks for the videos!

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: Stoker on May 28, 2019, 10:28:16 am

That's great .... sort of like stereo!  ;c)

Title: Memorial Day engine run
Post by: MasonvilleEngines on May 28, 2019, 08:02:10 am

https://youtu.be/HxqJhJiM_ek

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on April 12, 2019, 03:25:00 pm

Under load...Need a little more tension on spring holding needle pin...
https://youtu.be/V7d1JiN6Ktk

Gonna run the of gas of this one, will try to get another on bench if anyone interested.

Len.

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on April 12, 2019, 03:20:17 pm

https://youtu.be/lWnG8MuxOWc


Hit and Miss

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on April 12, 2019, 03:19:16 pm

Had a tap and bolt, put a hole in center, runs better...
https://youtu.be/YgvBfzOf2fw

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on April 12, 2019, 03:12:39 pm

This one came from Herb with a hole that accepts a 5/16 tap ( blue one took a 10-24 tap)

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on April 10, 2019, 10:20:17 am

Finally have another on bench...

https://youtu.be/wzGyuZRaxYc

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on April 04, 2019, 04:03:48 am

Based on the you tube id , I am sure Doug may be able to add more info...

http://www.steamenginemodels.com/Tiny%20Power.html

Once upon a time I ordered a casting set, advertised as "can be built with drill press". My drill press was not big enough so I was unable to complete several of the operations alluded to in the provided blueprint. Many years later I met Herb and eventually the fly wheels were drafted for the above blue engine.

Will take video when I get another engine on bench.

Len.

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: Jim on April 03, 2019, 08:34:57 pm

Quote from: MasonvilleEngines on March 27, 2019, 06:17:04 pm

The roll pin is in the intake

I will not hit and miss right without it. Needs a bit or bob. The Flywheels are from this tiny steam...met a gasser first.


https://youtu.be/7AaCrE6Yv0g

Were these engines US built?

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: Nick on April 03, 2019, 08:28:53 pm

Really enjoying these videos, keep them coming  8)

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on April 03, 2019, 02:59:20 pm

Final run for this one for now...
https://youtu.be/opt7XN8XNHk

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on March 31, 2019, 07:03:13 am

Hi all,
 Roll pin replaced with more permanent fix, used a 10-24 thread in case hole size needs to be adjusted for altitude.

Len.

Title: Re: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on March 27, 2019, 06:17:04 pm

The roll pin is in the intake :o

I will not hit and miss right without it. Needs a bit or bob. The Flywheels are from this tiny steam...met a gasser first.


https://youtu.be/7AaCrE6Yv0g

Title: Running Herb Bedell Engines...you put a roll pin where?
Post by: MasonvilleEngines on March 25, 2019, 02:59:09 pm

Hi all,
 I love roll pins  :o

Len.

https://youtu.be/S1BiXWvJV6E