Office of Steam Logo_1

« previous next »
Pages: [1]

Author Topic: Breisch/Peters old flame licker  (Read 2332 times)

  • Sr. Member
  • ****
  • Posts: 1818
  • Location: The Winter Wonderland, Michigan.
Breisch/Peters old flame licker
« on: March 09, 2020, 07:25:26 pm »
Here is my old Breisch/Peters flame licker.  From an old cast iron kit. Needed some tweaking, hope you enjoy.



Logged
Tommy

"Steam it, like you mean it."

  • Administrator
  • Engineer
  • *****
  • Posts: 9191
  • Location: Minnesota, USA 🇺🇸
Re: Breisch/Peters old flame licker
« Reply #1 on: March 09, 2020, 09:32:04 pm »
That looks like a nice heavy lump running well  8)  Does it have any power?
Logged
Nick

  • Sr. Member
  • ****
  • Posts: 1818
  • Location: The Winter Wonderland, Michigan.
Re: Breisch/Peters old flame licker
« Reply #2 on: March 09, 2020, 09:43:01 pm »
Yeah it's a lump alright. Roughly the same size as the PM Research but all cast iron except for the pulley.
Logged
Tommy

"Steam it, like you mean it."

  • Jr. Member
  • **
  • Posts: 245
  • Crisis?...What crisis?
  • Location: Gurnee Illinois USA
Re: Breisch/Peters old flame licker
« Reply #3 on: March 10, 2020, 04:01:06 pm »
Enjoyed seeing your engine running and it certainly runs well :)
Logged
PAUL
Civilization is the limitless multiplication of unnecessary necessities.

  • Sr. Member
  • ****
  • Posts: 1818
  • Location: The Winter Wonderland, Michigan.
Re: Breisch/Peters old flame licker
« Reply #4 on: March 11, 2020, 03:21:21 pm »
Quote from: Belugawhaleman on March 10, 2020, 04:01:06 pm
Enjoyed seeing your engine running and it certainly runs well :)

Thanks Paul.
Logged
Tommy

"Steam it, like you mean it."

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 2529
  • Location: Jutland
    • www.SteamUp.dk
Re: Breisch/Peters old flame licker
« Reply #5 on: March 12, 2020, 06:46:20 am »
What a nicely running rugged looking engine that, thanks for sharing Tom  :)
Logged
Cheers
Jan
WEBSITE: SteamUp YOUTUBE: SteamUp

  • Sr. Member
  • ****
  • Posts: 1016
  • Location: Ontario, Canada
Re: Breisch/Peters old flame licker
« Reply #6 on: March 12, 2020, 08:30:26 am »
That really looks like a good runner, all right, way better than mine. I made a flame licker from scratch once, and I got maybe two pops out of it before giving up and shelving it.
Logged
Bob

  • Sr. Member
  • ****
  • Posts: 1818
  • Location: The Winter Wonderland, Michigan.
Re: Breisch/Peters old flame licker
« Reply #7 on: March 14, 2020, 05:47:29 pm »
Quote from: Hero on March 12, 2020, 08:30:26 am
That really looks like a good runner, all right, way better than mine. I made a flame licker from scratch once, and I got maybe two pops out of it before giving up and shelving it.



Bob get it off the shelf and on the work bench. I got this off of Ebay, a bit dirtier and it wouldn't pop at all. I added the pulley just so there was something to grab when turning it over. I cleaned it, and played with lining everything back up, adjusting this and that. Was about to give up and then it happened,  it popped, and then another. Then two, three and so on. It started to warm up.  All it needed was to be freed up good. No drag anywhere and a good seal on the gate when slides open and closed. A good seal when turning it over slowly with no flame, sounds like it's farting. It will run Bob.
Logged
Tommy

"Steam it, like you mean it."
Pages: [1]
« previous next »