Office of Steam Logo_1

« previous next »
Pages: 1 2 [3] 4 5

Author Topic: Vertical Transmission Build  (Read 3877 times)

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #30 on: April 01, 2019, 06:43:56 pm »
Quote from: jkbixby on April 01, 2019, 09:03:24 am
I really like following this thread, learning a lot - just wish I could work in metal. I was surprised to see you using Cold Galvanizing as an undercoat as I wouldn't have thought it would work out okay with normal paint (no knowledge just seat of the pants thinking) but apparently it does - the only place I've ever used it is on the valley flashing on my house roof.
Larry I wish I could craft wood like you do. The cold gal works very well on ferrous metals.
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #31 on: April 01, 2019, 06:44:51 pm »
Quote from: Stoker on April 01, 2019, 09:54:44 am
Nice build thread here Jim!

Also nice handles for your mill .... but I do find gripping aluminum blackens my hands to some extent.
Thanks Daniel, I've never found that with ali I wonder if it has something to do with grades of ali or just the end uses skin pH?
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #32 on: April 01, 2019, 06:49:28 pm »
Thread done -

[ Guests cannot view attachments ]



[ Guests cannot view attachments ]

Parting off -

[ Guests cannot view attachments ]



[ Guests cannot view attachments ]



[ Guests cannot view attachments ]
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #33 on: April 01, 2019, 06:51:48 pm »
Bolt put into a tapped offcut mandrel -

[ Guests cannot view attachments ]




Remove the nub -

[ Guests cannot view attachments ]



[ Guests cannot view attachments ]




Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #34 on: April 01, 2019, 06:55:27 pm »
Using a small hand file to bevel the top of the bolt -

[ Guests cannot view attachments ]



Mandrel removed from the chuck -
[ Guests cannot view attachments ]



Buffing on a coarse mop (still held in the mandrel) -

[ Guests cannot view attachments ]



Buff on the loose calico mop -

[ Guests cannot view attachments ]



1x bolt made, 3x to go!

[ Guests cannot view attachments ]



[ Guests cannot view attachments ]
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #35 on: April 01, 2019, 06:57:15 pm »
Measuring the bolt head for length before parting off. I always use the first item made as the template for others. Probably an unorthodox method and trained engineers maybe raising their eyebrows, but it works for me and I suppose being untrained gives me freedom to just do what works for me -

[ Guests cannot view attachments ]



4x bolts made -

[ Guests cannot view attachments ]
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #36 on: April 01, 2019, 06:58:42 pm »
Steel out of the oven now and paint fully cured and having a test fit on the wooden plinth -

[ Guests cannot view attachments ]



[ Guests cannot view attachments ]



[ Guests cannot view attachments ]
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #37 on: April 01, 2019, 06:59:39 pm »
Drilled and tapped the holes for the brass bolts in the hardwood -

[ Guests cannot view attachments ]
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #38 on: April 01, 2019, 07:03:23 pm »
Turned some brass washers up for under the bolts -

[ Guests cannot view attachments ]



Bolted down to the wooden plinth -

[ Guests cannot view attachments ]



[ Guests cannot view attachments ]




[ Guests cannot view attachments ]




  [ Guests cannot view attachments ]


Stainless steel axles cut -


[ Guests cannot view attachments ]      




Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #39 on: April 01, 2019, 08:43:05 pm »
50mm Aluminium bar in chuck (its about 51.5mm) -
[ Guests cannot view attachments ]



Blued, measured and marked -
[ Guests cannot view attachments ]



Starting on the different sizes -

[ Guests cannot view attachments ]



[ Guests cannot view attachments ]



[ Guests cannot view attachments ]



[ Guests cannot view attachments ]



[ Guests cannot view attachments ]



[ Guests cannot view attachments ]
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Full Member
  • ***
  • Posts: 356
  • Location: Michigan
Re: Vertical Transmission Build
« Reply #40 on: April 02, 2019, 01:02:17 am »
Quote from: Jim on April 01, 2019, 06:59:39 pm
Drilled and tapped the holes for the brass bolts in the hardwood -


Will the tapped holes in the wood hold it or did you use t-nuts on the under side?
Logged
Carl "There is a better way for everything. Find it."TAE

​

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #41 on: April 02, 2019, 01:31:59 am »
Quote from: Mi Steam on April 02, 2019, 01:02:17 am
Will the tapped holes in the wood hold it or did you use t-nuts on the under side?
Hi Carl, no nuts just the bolts nipped down onto the hardwood. They torque up very well in this wood as its extremely dense stuff.
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #42 on: April 02, 2019, 01:37:01 am »
Centre drilling  -

[ Guests cannot view attachments ]



Using a revolving centre for making the belting grooves on the pulleys -

[ Guests cannot view attachments ]




Checking the depth for the green belting -
[ Guests cannot view attachments ]



More grooving -
[ Guests cannot view attachments ]

Finished the grooving process -
[ Guests cannot view attachments ]

Drilling through for the axle shaft -
[ Guests cannot view attachments ]




[ Guests cannot view attachments ]




Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #43 on: April 02, 2019, 01:39:46 am »
All polished up now and starting to part off -

[ Guests cannot view attachments ]



Parted off -

[ Guests cannot view attachments ]



Took some time, but I'm happy how that's turned out -

[ Guests cannot view attachments ]
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Administrator
  • Engineer
  • *****
  • Posts: 6272
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Vertical Transmission Build
« Reply #44 on: April 02, 2019, 01:42:41 am »
Turned it around in the chuck to clean up the back -
[ Guests cannot view attachments ]



[ Guests cannot view attachments ]



[ Guests cannot view attachments ]



[ Guests cannot view attachments ]




Decorative groove -

[ Guests cannot view attachments ]




Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

Pages: 1 2 [3] 4 5
« previous next »