Office of Steam Logo_1

« previous next »
Pages: 1 2 3 [4]

Author Topic: Large model Boiler project  (Read 2432 times)

  • Global Moderator
  • Engineer
  • *****
  • Posts: 5596
  • Location: St. Paul Indiana
Re: Large model Boiler project
« Reply #45 on: September 02, 2021, 08:20:21 pm »
That engine would be a perfect companion for this boiler I think.
Logged
Bruce, St. Paul Indiana, USA
"Originality thrives in seclusion free of outside influences beating upon us to cripple the creative mind."
  Nikola Tesla

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4122
  • Location: Plano, Texas
Re: Large model Boiler project
« Reply #46 on: September 03, 2021, 06:33:39 pm »
Quote from: RedRyder on September 02, 2021, 07:20:35 pm
Quote from: parallelmotion on September 01, 2021, 08:01:37 am
Scott had a 1/2 hp Sipp which I think will be FS.

Yes.... I believe he got it from me (if it is this one).

Gil





(Attachment Link)

It is the one. :)
Logged

  • Global Moderator
  • Engineer
  • *****
  • Posts: 5596
  • Location: St. Paul Indiana
Re: Large model Boiler project
« Reply #47 on: September 06, 2021, 04:05:38 pm »
Hi Folks
I got a bit more plumbing installed & had a nice steam up



another test of the S/V



I knocked this out & its been such a help in filling the boiler , screws right into the 1/4 npt hole in the top of the boiler and only takes about 30 seconds to fill the boiler now.



now to install the water injector...
Logged
Bruce, St. Paul Indiana, USA
"Originality thrives in seclusion free of outside influences beating upon us to cripple the creative mind."
  Nikola Tesla

  • Administrator
  • Engineer
  • *****
  • Posts: 5070
  • Location: Connecticut - USA
Re: Large model Boiler project
« Reply #48 on: September 06, 2021, 04:39:10 pm »
Superb!   That boiler has plenty of grunt and it ought to keep up with a good sized engine quite nicely.
Logged

  • Global Moderator
  • Engineer
  • *****
  • Posts: 5596
  • Location: St. Paul Indiana
Re: Large model Boiler project
« Reply #49 on: September 06, 2021, 05:09:38 pm »
Quote from: RedRyder on September 06, 2021, 04:39:10 pm
Superb!  That boiler has plenty of grunt and it ought to keep up with a good sized engine quite nicely.
Thanks Gil, running a big engine (or 2) is the plan. 😊👍
Logged
Bruce, St. Paul Indiana, USA
"Originality thrives in seclusion free of outside influences beating upon us to cripple the creative mind."
  Nikola Tesla

  • Administrator
  • Engineer
  • *****
  • Posts: 6285
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Large model Boiler project
« Reply #50 on: September 06, 2021, 09:15:54 pm »
Enjoying following this thread Bruce :)
Logged
_______________________________________________
Cheers.
Jim

Blue Heelers Model & Toy Steam Engine Room YouTube Channel -
 https://www.youtube.com/user/Blue123Heeler/videos

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4122
  • Location: Plano, Texas
Re: Large model Boiler project
« Reply #51 on: September 07, 2021, 04:34:03 pm »
Quote from: Jim on September 06, 2021, 09:15:54 pm
Enjoying following this thread Bruce :)

Me too Jim!

And hopefully two suitable engines will be delivered to Bruce at Cabin Fever. :)
Logged

  • Global Moderator
  • Engineer
  • *****
  • Posts: 5596
  • Location: St. Paul Indiana
Re: Large model Boiler project
« Reply #52 on: September 18, 2021, 01:53:14 pm »
Hi folks
got a few more things done to the big boiler

I made some oak knobs for the steam valves (not sure if I like em' yet) but the grain of the wood runs with the valve handle so it easy to tell when they're off/on. I put a copper sleeve in them to make them a bit tighter on the valve handle.

I started off with a nice piece of Oak & used a hole cutter with the center drill raised all the way up.


then I used a end mill to cut the slot



I started off with 1.1/8" OD & found it just to small, I went with the next size up which was 1 5/16"






[URL=https://app.photobucket.com/u/bruceang1/p/d2fcf47d-838e-4d05-b1ec-cc9d3e5b967a]



I bought a nice little Brass whistle w/valve from Ebay
https://www.ebay.com/itm/324004916113?hash=item4b7032ab91:g:bZ4AAOxyaURTfWcS



it sounds a little tinny & air wheezy ...but that's just the proximity of my camera , I can assure you its quite crisp & clear.
Logged
Bruce, St. Paul Indiana, USA
"Originality thrives in seclusion free of outside influences beating upon us to cripple the creative mind."
  Nikola Tesla
Pages: 1 2 3 [4]
« previous next »