Office of Steam Logo_1

Author Topic: Stuart Beam Engine Governor  (Read 220 times)

Brad

  • Jr. Member
  • **
  • Posts: 242
Stuart Beam Engine Governor
« on: January 05, 2022, 11:00:29 am »
 have started to make the governor for my Stuart beam engine. I want to capture the look of an early Watt governor

Quickj

  • Jr. Member
  • **
  • Posts: 265
  • Location: Minnetonka, Minnesota, USA
Re: Stuart Beam Engine Governor
« Reply #1 on: January 05, 2022, 11:52:06 am »
Looking good so far.
A complex system that does not work is invariably found to have evolved from a simple system that worked just fine.
View/Subscribe to my YouTube channel.
https://www.youtube.com/channel/UCv2_Ao6XtHt9bXvJCiKYtpw

txlabman

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3589
  • Location: Plano, Texas
Re: Stuart Beam Engine Governor
« Reply #2 on: January 05, 2022, 02:16:22 pm »
 
Very nice Brad.


Brad

  • Jr. Member
  • **
  • Posts: 242
Re: Stuart Beam Engine Governor
« Reply #3 on: January 05, 2022, 03:08:31 pm »
Moving along. Got to make smaller balls as they look out of scale.

txlabman

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3589
  • Location: Plano, Texas
Re: Stuart Beam Engine Governor
« Reply #4 on: January 05, 2022, 05:43:35 pm »

Those are definitely some big balls!  :)

St Paul Steam

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4831
  • Location: St. Paul Indiana
Re: Stuart Beam Engine Governor
« Reply #5 on: January 05, 2022, 07:14:44 pm »
Looking good Brad , your Watts scale looks correct.
Bruce, St. Paul Indiana, USA
"Originality thrives in seclusion free of outside influences beating upon us to cripple the creative mind."
  Nikola Tesla

Brad

  • Jr. Member
  • **
  • Posts: 242
Re: Stuart Beam Engine Governor
« Reply #6 on: January 06, 2022, 02:18:30 pm »
I fitted the finished parts to the engine. Closely matches those on small beam engines in the Henry Ford Museum. Don't pay attention to the Phillips head screws. They will be gone when my 0-80 hex-head bolts and nuts arrive.

parallelmotion

  • Full Member
  • ***
  • Posts: 511
Re: Stuart Beam Engine Governor
« Reply #7 on: January 06, 2022, 03:14:55 pm »
Looking good Brad. What's wrong with big balls?

Brad

  • Jr. Member
  • **
  • Posts: 242
Re: Stuart Beam Engine Governor
« Reply #8 on: January 06, 2022, 03:34:59 pm »
Use any size that looks good to you. I prefer to keep the aesthetics close to what is in my photos of the small beam engines at the Ford Museum. There is so much science to centrifugal motion. RPM, weight of governor balls, amount of work to be done. etc. Since a model engine governor usually does not actually govern unless the engine is run at warp speed, I choose to stick with what looks right. I run my engines at scale speed, which for a small beam engine like the Stuart, would be about 45 RPM. It is a model and I feel it should look prototypical.

Quickj

  • Jr. Member
  • **
  • Posts: 265
  • Location: Minnetonka, Minnesota, USA
Re: Stuart Beam Engine Governor
« Reply #9 on: January 06, 2022, 03:37:32 pm »
Looks really good to me.  I have always liked the Stuart Beam.

A complex system that does not work is invariably found to have evolved from a simple system that worked just fine.
View/Subscribe to my YouTube channel.
https://www.youtube.com/channel/UCv2_Ao6XtHt9bXvJCiKYtpw

Brad

  • Jr. Member
  • **
  • Posts: 242
Re: Stuart Beam Engine Governor
« Reply #10 on: January 06, 2022, 03:40:20 pm »
I always did too and it is a very nice runner. The simplistic design makes it robust. I am also working on an M E Beam engine and it is much more fickle. Beautiful engine, but not robust.

tenniV11

  • Full Member
  • ***
  • Posts: 995
  • that's all I have to say about that
  • Location: Switzerland - Lake of Constance
    • Emco Unimat
Re: Stuart Beam Engine Governor
« Reply #11 on: January 07, 2022, 03:18:15 am »
Good job on that Governor
I have the same Beam Engine and here a picture
of my governor, Have a nice day, Arnold :D

[ Guests cannot view attachments ]

Brad

  • Jr. Member
  • **
  • Posts: 242
Re: Stuart Beam Engine Governor
« Reply #12 on: January 07, 2022, 08:56:10 am »
Does the spring drive work well? I am planning to use an O-ring.

txlabman

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3589
  • Location: Plano, Texas
Re: Stuart Beam Engine Governor
« Reply #13 on: January 07, 2022, 10:04:45 am »
Use any size that looks good to you. I prefer to keep the aesthetics close to what is in my photos of the small beam engines at the Ford Museum. There is so much science to centrifugal motion. RPM, weight of governor balls, amount of work to be done. etc. Since a model engine governor usually does not actually govern unless the engine is run at warp speed, I choose to stick with what looks right. I run my engines at scale speed, which for a small beam engine like the Stuart, would be about 45 RPM. It is a model and I feel it should look prototypical.

Thoughtful and well said Brad!

tenniV11

  • Full Member
  • ***
  • Posts: 995
  • that's all I have to say about that
  • Location: Switzerland - Lake of Constance
    • Emco Unimat
Re: Stuart Beam Engine Governor
« Reply #14 on: January 07, 2022, 01:07:35 pm »
Does the spring drive work well? I am planning to use an O-ring.

The problem is that the bronze balls are very heavy and without a
spring they have too much travel at low speed. With the spring it is really
a fully functional governor. Regards, Arnold