Office of Steam Logo_1

Author Topic: Flat Belt Drive Pulley Camber  (Read 695 times)

Jim

  • Administrator
  • Hero Member
  • *****
  • Posts: 4330
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Flat Belt Drive Pulley Camber
« on: May 21, 2019, 08:04:19 pm »
I'm turning up an aluminium pulley for a PMR Generator.

For a pulley for a flat belt, how much camber is needed on the pulley for the flat belt to center itself?
_______________________________________________
Cheers.
Jim

My YouTube Channel https://www.youtube.com/user/Blue123Heeler/videos


Stoker

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3616
  • Wherever you go ......... there you are!
  • Location: Eastern Sierra
Re: Flat Belt Drive Pulley Camber
« Reply #1 on: May 21, 2019, 08:59:42 pm »
Tough question Jim!

There are a whole host of variables involved here that I doubt you'd want or need to go into, but they include the diameter and width of the pulley, the type of belting material and its width and thickness, plus the span between the pulleys, plus the crown or lack there of for the other pulley, and no doubt speed and power factor in as well.

There is also the form of the crown, whether it is a smooth curve, a simple ridge with flat lead in angles, or a flat across the top with just the edges forming tapered angles.

My feeling is that if you crown it just enough so that you can actually see the crown, that will likely be about right .... say about .015-.020 per inch, and if that doesn't do it, add a bit more.
"Information is not knowledge, Knowledge is not wisdom, Wisdom is not truth, Truth is not beauty, Beauty is not love, Love is not music: Music is THE BEST...   
Wisdom is the domain of the Wis (which is extinct). Beauty is a French phonetic corruption of a short cloth neck ornament currently in resurgence..."
F. Zappa ... by way of Mary, the girl from the bus.

Jim

  • Administrator
  • Hero Member
  • *****
  • Posts: 4330
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Flat Belt Drive Pulley Camber
« Reply #2 on: May 21, 2019, 09:53:54 pm »
Thanks Daniel, its been a frustrating experience so far with trying to get the PMR belting track right on pulleys and not continuously jumping off.

I'm not overly enthused about the superglue joint that I did either, I think I may have overlapped it too much as there is a distinct 'thud' each time it goes round a pulley.

I've toyed with the idea of doing a butt join and using some soft braided fishing line (like Firewire etc) to join the belt like the old school method of joining leather belting.
_______________________________________________
Cheers.
Jim

My YouTube Channel https://www.youtube.com/user/Blue123Heeler/videos


Nick

  • Administrator
  • Engineer
  • *****
  • Posts: 8116
  • Location: Minnesota, USA
Re: Flat Belt Drive Pulley Camber
« Reply #3 on: May 21, 2019, 11:39:12 pm »
I've toyed with the idea of doing a butt join and using some soft braided fishing line (like Firewire etc) to join the belt like the old school method of joining leather belting.

I did this when belting my Case to a burr mill, but instead of a butt, I angled the ends with a razor blade so when pieced together it was overlapped and flat, then I just ran it through a sewing machine.
Nick

Weedensteam

  • Full Member
  • ***
  • Posts: 339
    • WeedenSteam
Re: Flat Belt Drive Pulley Camber
« Reply #4 on: May 21, 2019, 11:40:01 pm »
Is it possible to run the belt crossed, most old timers claim they run best that way, some even doubled twisted them so as not to reverse direction.
Frank C.
http://weedensteam.com
       - engine identification and parts

Nick

  • Administrator
  • Engineer
  • *****
  • Posts: 8116
  • Location: Minnesota, USA
Re: Flat Belt Drive Pulley Camber
« Reply #5 on: May 21, 2019, 11:51:50 pm »
Is it possible to run the belt crossed, most old timers claim they run best that way, some even doubled twisted them so as not to reverse direction.

A half twist will also keep it from going side to side while not changing direction. This helps reduce slap and reduces wear as the pulleys are making contact on both sides of the belt.
Nick

St Paul Steam

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4831
  • Location: St. Paul Indiana
Re: Flat Belt Drive Pulley Camber
« Reply #6 on: May 22, 2019, 06:24:08 am »
Jim, I have made a few flat belts & have been to a few leather shops that join leather belts, they have a tool that is adjustable & can strip half of the thickness away , I just do that to both sides, I have also used my 1" belt sander to thin the belt to about half thickness, then  I join with "Barge" all purpose cement (suggested by the leather shop) also make sure your belt is "set" dead straight, using a long ruler as this will obviously effect alignment, compress with a clamp (block of wood works well with wax paper above & below the joint) & let set for 24 hrs, & as Daniel has said re; camber "just enough so that you can actually see the crown" is all that is needed on the camber.

Bruce, St. Paul Indiana, USA
"Originality thrives in seclusion free of outside influences beating upon us to cripple the creative mind."
  Nikola Tesla

jkbixby

  • Full Member
  • ***
  • Posts: 998
  • Location: Gahanna, Ohio
Re: Flat Belt Drive Pulley Camber
« Reply #7 on: May 22, 2019, 04:24:59 pm »
Thanks Daniel, its been a frustrating experience so far with trying to get the PMR belting track right on pulleys and not continuously jumping off.

Jim, you might want to just contact PMR with your problem and info - they're pretty nice about helping out.
Regards,
Larry

Jim

  • Administrator
  • Hero Member
  • *****
  • Posts: 4330
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Flat Belt Drive Pulley Camber
« Reply #8 on: May 23, 2019, 02:36:00 am »
Thanks one and all for all the advice, very much appreciate everyone's post.
_______________________________________________
Cheers.
Jim

My YouTube Channel https://www.youtube.com/user/Blue123Heeler/videos


Mi Steam

  • Full Member
  • ***
  • Posts: 353
  • Location: Michigan
Re: Flat Belt Drive Pulley Camber
« Reply #9 on: May 25, 2019, 12:56:20 am »
Jim, I am getting late into this about making belts. I was out of town
and did not have the photos I needed. I have run a PMR with an S50
with no trouble in this way. When I make belts for Edison cylinder
phonographs. This how I made them and it has worked well for me
when running the PMR.

[ Guests cannot view attachments ]

I cut the ends on an angle and overlap a 1/2”. Then thinned the top of one
end of the belt. Then thinned the bottom of the other end sow that they are
now the same thickness.

[ Guests cannot view attachments ]

Hope this is some help as it has worked for me.
Carl "There is a better way for everything. Find it."TAE


Jim

  • Administrator
  • Hero Member
  • *****
  • Posts: 4330
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Flat Belt Drive Pulley Camber
« Reply #10 on: May 26, 2019, 07:37:04 pm »
Thank you very much Carl, very much appreciated!
_______________________________________________
Cheers.
Jim

My YouTube Channel https://www.youtube.com/user/Blue123Heeler/videos



Nick

  • Administrator
  • Engineer
  • *****
  • Posts: 8116
  • Location: Minnesota, USA
Nick

Jim

  • Administrator
  • Hero Member
  • *****
  • Posts: 4330
  • Aussie Steamer always on the boil :)
  • Location: South Coast of New South Wales Australia
Re: Flat Belt Drive Pulley Camber
« Reply #13 on: May 26, 2019, 10:56:44 pm »
That's an interesting looking tool Frank.

_______________________________________________
Cheers.
Jim

My YouTube Channel https://www.youtube.com/user/Blue123Heeler/videos


St Paul Steam

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 4831
  • Location: St. Paul Indiana
Re: Flat Belt Drive Pulley Camber
« Reply #14 on: May 27, 2019, 06:35:51 am »
 I found this video.

Bruce, St. Paul Indiana, USA
"Originality thrives in seclusion free of outside influences beating upon us to cripple the creative mind."
  Nikola Tesla